CNC 400*280mm DIY MINI Wood Route

-

CNC 400*280mm Laser Machine DIY MINI Wood Router For Cutting Engraving Milling Tools

Engraving materials: wood, plastic, paper, bamboo, horn, part of leather (wallet), plastic phone case, rubber stamp, photosensitive chapter, sponge paper, etc.
Input voltage：AC 100V-240V，50 / 60Hz
Output：DC 12V 5A
Engraving area：400*280mm
Support software include: weidiao master, GRBL. etc.
Support PWM TTL modulate laser power
Support gray engraving, sketch route cutting, line scanning engraving, spot engraving.etc

评论

发表评论

此博客中的热门博文

TC55V 4 axis with 3.5 Inch Color LCD CNC controller

-
图片
Main Functions Automatically execute:Actual running, Dry running, Single-step execution, Terminate program, Start and Pause function Manual operation:Manual high speed, Manual low speed, Jog operation, Back to program zero, Back to machine zero Program management:absolute programming, Incremental programming, linear and circular interpolation, back to machine zero, sub-program call,register, delay, repeat, Output, PLC set, Pause Parameter settings:Set various control parameters of processing and operation, get the best status of processing effect Exterior Manual Operation: control motor clockwise and counter-clockwise spinning, Start, Pause, Alert and Emergency Stop. USB Connection and upgrade PLC Extension I/O Extension Isolated I/O port Chinese/English panel display Free change of boot picture Technical Specifications Minimum data unit 0.001 mm Maximum data size ± 99999.999mm Maximum Speed: 9000mm/min (pulse is 0.001mm) Maximum pulse output frequenc
More »

XHC MKX-M4 Mach4 USB Motion Card

-
图片
  1 PCS x Mach4  3/4/6 Axis  USB Motion Card Interface  2000KHz xhc mach3 motion card manual Features 1. Supporting Mach4 Hobby version . 2. Support spindle speed feedback . 3. Full support for USB hot-swappable, the card is Monitoring . 4. USB connection status at any time.  5. Supports Up 6-axis,support differential output Maximum step-pulse frequency is 2000KHz . 6. Status indicator LED can be useful to show the USB . 7. connection, and working status by flashing. 16 general-purpose input . 8. has speed function, the spindle actual speed Mach4  interface in real-time display . 9. all IO-port isolation, interference, stable performance.   Support: 3-axis or 4-axis, or 6-axis Mk3-M4: 3-axis; Mk4-M4: 4-axis: Mk6-M4: 6-axis NOTE: If the inverter is turned on, the control card is not working properly because of interference caused by the inverter; Replace inverter. Input IO Connect Mechanical switch or NPN (PNP) Photoelectric switch Input signal must be active low.
More »

XHC Ethernet 3/4/6 Axis MACH3 CNC Motion Control Card

-
图片
  Fully supporting all Mach3 versions， support Windows PC. ·Only support Ethernet interface, Need to set IP address. ·Support save data when power off ·Support spindle speed feedback ·Support 10 meters Ethernet interface cable ·Supports Up 6-Axis ·Maximum step-Pulse frequency is 2000KHz 16 general-prupose input, 8 output. ·Velocity feedback function , Spindle speed display in real time ·All IO-port isolation , interference, stable performance ·Support servo motor and step motor 1 PCS x  3/4/6 Axis ETHERNET MOTION CARD  Interface 2000KHz Support : 3-Axis or 4-Axis , or 6-Axis MK3-IV : 3-Axis ; MK4-IV : 6-Axis ; MK6-IV : 6-Axis xhc mach3 motion card manual
More »